1970 Mustang Mach1 World Registry Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.
1970 Mustang Mach1 World Registry Forum

Welcome to the 1970 Mustang Mach1 World Registry this forum is open to all 1970 Mach1 owners & enthusiast around the world.
 
HomeHome  SearchSearch  Latest imagesLatest images  RegisterRegister  Log inLog in  

 

 Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b

Go down 
2 posters
AuthorMessage
Alan_MacDougall
New Member



Number of posts : 6
Registration date : 2010-02-14

Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b Empty
PostSubject: Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b   Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b EmptyTue 16 Feb - 22:04

I recently had both full quarter panels replaced and we just noticed the side maker holes were not cut in the Dynacorn panels. Crying or Very sad We can get the hole size and the vertical height location off the old panels but we need the horizontal location measurements from an original panel. Please can someone measure accurately with a straight edge from the rear edge of the light housing or (better from the hole) to the of the edge of the quarter panel undercut for the bumper? Since this undercut edge is on an angle, I need two measurements , a) at the top b) at the bottom of the light housing or hole. Another method would be to use tracing paper and trace the hole and the edge and send it to me. HELP! I have to get the holes located correctly. any other suggestions? Alan 503 352-4930
Back to top Go down
brick70
Mach1 Addiction



Number of posts : 52
Registration date : 2008-04-03

Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b Empty
PostSubject: Re: Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b   Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b EmptyWed 17 Feb - 9:32

Hello, One way if you haven't trashed your old qtrs is to cut out the piece that has the opening and use it as an overlay to cut out the square. Be very careful it's better to cut it out a little smaller and file it later than to cut it to big and have cracks exposed outside the bezel.
Back to top Go down
Alan_MacDougall
New Member



Number of posts : 6
Registration date : 2010-02-14

Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b Empty
PostSubject: Re: Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b   Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b EmptyWed 17 Feb - 11:37

The old panels were cut to the left and right side of the holes such that there is no horizontal reference point. I can use the holes for vertical location and size. Alan
Back to top Go down
Sponsored content





Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b Empty
PostSubject: Re: Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b   Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b Empty

Back to top Go down
 
Quarter Panel Side Marker Light Hole Location [b]--HELP--[/b
Back to top 
Page 1 of 1
 Similar topics
-
» shaker hood cutout issues on location of hole
» Reproduction Sun-X Tinted Quarter Glass
» MAP LIGHT WIRING
» Turn signal "clicker"???
» 70 PARKING LIGHT ASSEMBLIES

Permissions in this forum:You cannot reply to topics in this forum
1970 Mustang Mach1 World Registry Forum :: DISCUSSIONS :: Tech Discussion (Q&A), Problems, Fixes. etc..-
Jump to: